- Some operators are returning to workshops because tachographs installed during earlier replacement phases now require updates.
- An incorrect manual entry remains in the tachograph’s data. Marek Stawowczyk recommends printing the relevant record and explaining the mistake on the printout.
- According to LONTEX’s experience, truck drivers who have used tachographs for years generally have fewer basic operating problems than drivers encountering the equipment for the first time in vans.
- In Stawowczyk’s view, businesses operating vehicles up to 3.5 tonnes were better prepared for the new requirement than some operators had been during the tachograph replacement programme in 2024.
- Regular training helps drivers avoid manual-entry mistakes, understand night-work rules and plan reduced rest periods correctly.
trans.INFO: Carriers have already gone through several stages of mandatory tachograph replacement. What issues are most often bringing them back to workshops now?
Marek Stawowczyk, LONTEX:
At present, updates are the most common reason operators return to the workshop. Some of the tachographs fitted during the first replacement wave in 2024 now need to be updated.
That can be difficult for carriers to understand. They have only recently paid for a new device and its installation, and now they have to visit the workshop again. The update is chargeable, so it represents another expense.
We also deal with routine operating faults, including issues involving GNSS, the satellite positioning system, and signal loss. These are part of routine servicing, however. When there is a genuine hardware fault, the authorised service centre handles it.
Now that the replacement programme is largely complete, are serious technical problems with the new tachographs still appearing?
From our perspective, the situation is fairly stable. The biggest difficulties came during the replacement itself, when equipment availability and installation schedules caused problems.
The tachographs are now operating normally. Any device can fail, of course, but we are not currently seeing a distinct wave of technical faults.
Another important stage will be the next calibration cycle for equipment installed during earlier replacement phases. It will provide another opportunity to verify that the devices are working correctly.
What about driver errors? Does the second-generation smart tachograph create difficulties for them?
For drivers of heavy goods vehicles, relatively little has changed in day-to-day operation.
They have often worked with tachographs for years, so they know the basic rules and understand how to use the equipment. The new generation adds further functions, but it has not radically changed the driver’s basic interaction with the device.
In some respects, the new systems make things more convenient. Bluetooth communication is one example. In suitably equipped vehicles, and with the right applications, drivers can access selected functions through a smartphone.
The greater challenge is in the vehicle segment up to 3.5 tonnes, where many drivers are only now beginning to work with tachographs.
So is a driver’s lack of experience a bigger problem than the device itself?
Exactly. Someone who has spent years driving without a tachograph must learn not only how to operate it, but also how to record each type of activity.
Manual entries are the biggest source of uncertainty. Drivers need to know what to enter, when to enter it and how to classify a particular period of activity correctly.
For an experienced truck driver, many of these steps become automatic. That is not necessarily the case for a new user.
Drivers sometimes confuse pictograms, dates or times. They may also be unsure how to record an activity correctly or when a particular rest-time option is available.
These are skills that have to be learned through practice.
Can a carrier run into trouble even when the tachograph is technically sound because the data was entered incorrectly?
Certainly. Manual entries are made by people, and people can make mistakes.
Once an entry has been confirmed and saved in the tachograph, it cannot simply be reversed and deleted.
If a driver notices an error, the best approach is to print the relevant tachograph record and write down what went wrong, together with the actual sequence of activities.
Downloading the data alone will not resolve the issue. The incorrect entry will still be visible in the device records.
So drivers should not assume that a mistake will disappear during the next data download?
No. If something was entered incorrectly and saved, it remains part of the tachograph data.
That is why drivers need to know how to document an error. A device can be functioning properly while some of the information stored in it is still incorrect.
Do you see a practical difference between large fleets and smaller carriers?
I would not divide businesses solely by the number of vehicles they operate. The more important questions are who uses the tachograph and how much experience they have.
Drivers working with heavy vehicles, tractor units or large transport fleets generally know the basic operating rules well.
At present, many more mistakes are being made by users of vehicles up to 3.5 tonnes who had no practical experience with tachographs before.
That is why we often provide training for these drivers. In some cases, it is only during the training that they begin to understand how the device should be used in their everyday work.
Vans and tachographs: manual entries remain the biggest hurdle
Since 1 July 2026, tachographs have also been required in vehicles and vehicle combinations with a gross vehicle weight above 2.5 tonnes when used for commercial international carriage of goods and for cabotage. After the first few months, how would you assess this segment’s level of preparation?
Honestly, I was positively surprised.
In my view, businesses operating vehicles up to 3.5 tonnes were better prepared for the new requirements than some heavy-vehicle operators had been during the earlier tachograph replacement stages.
The situation at the end of 2024 is a useful comparison. The availability of equipment and components was extremely limited then, while many carriers had postponed replacement until the last moment, expecting everything to be arranged immediately.
At one point, shortages affected almost every part of the process, while the prices of some components rose as much as fivefold.
The situation was different with vans. At least from our perspective, these businesses were more aware of the approaching requirement and started preparing for the change earlier.
What is the biggest challenge for van drivers today: operating the tachograph or adapting to the new driving and rest-time rules?
Feedback from drivers suggests that many of them appreciate having clear rules for working and resting. They know when to take a break and how to plan their rest.
Manual entries and the practical operation of the device are proving more difficult.
New users have to learn how to identify pictograms, enter dates and times correctly, record activities and understand what to do when a particular stage of work begins or ends.
They also need to understand the rest-time rules and the circumstances in which the options provided by the regulations can be used.
That takes practice. Drivers who have never used tachographs often make basic mistakes at first, but they gain confidence over time.
Is the instruction provided when the tachograph is installed enough to prepare a driver?
In my opinion, it is not. I always recommend dedicated tachograph training.
We have seen businesses install the equipment in vans without properly preparing their drivers to use it.
It is worth choosing trainers who understand both the equipment and the realities of transport operations.
That does not have to be training delivered by LONTEX. Many companies on the Polish market specialise in this area.
I would encourage carriers to arrange this training regularly, perhaps every year or two. Drivers can attend a training centre, or an instructor can visit the company.
You mentioned practical tips that drivers can learn during training. What do you have in mind specifically?
It is about understanding the rules and knowing how to apply them in everyday work. That includes recording night work correctly, making manual entries and choosing the right time to plan reduced rest.
Experienced practitioners know these matters well, but drivers are not always aware of every available option and limitation. Often, they simply follow the routine they have developed.
Training can show drivers how to use the tachograph correctly, organise their work more effectively and avoid mistakes. The aim is not to bypass the rules, but to understand and apply them properly.
After several months under the new rules for vans, can the industry say that the most difficult phase is over?
When it comes to installation, the situation is much calmer than it was during the earlier replacement programme for trucks.
But fitting a tachograph is only the first step. Correct operation, driver training and regular technical checks still follow.
The next calibration cycle for tachographs installed during the 2024 replacement programme is also approaching. We will once again verify that everything is working properly.
The key point is that carriers should not treat installation as a one-off task, after which no further checks are needed.
If you had to name one thing carriers should remember today to avoid tachograph-related problems, what would it be?
Driver training, above all.
A modern tachograph can be fully operational, but if the person using it does not know how to use it correctly, mistakes will continue.
Regular training gives drivers a chance to resolve uncertainties, refresh their knowledge and learn practical solutions for everyday work.
A tachograph is a tool. The important thing is knowing how to use it.









